![]() ![]() It must only be connected on the safe side of the isolator or barrier. This DIN rail-mounted unit provides RS-485 Modbus RTU Slave communications for one ExTemp sensor. When using the LCT adaptor the free downloadble Calex Config Software may be used for configuration of the sensor and display of the measurement. The adapter is connected to the measurement loop via mini-hook connectors. The free Windows-compatible configuration software allows the user to rescale the 4-20 mA output, adjust the emissivity setting, and configure averaging, hold processing and reflected energy compensation. LCT Loop Configuration Tool (USB Adapter)Īll ExTemp models are fully configurable via the optional USB adapter (must only be connected on the safe side of the isolator or barrier). Special Temperature Range (temperature range is scalebable from -20☌ to 1000☌ via optional adapters and software)Ĭontact IOThrifty for information on longer cable lengths.Select the following options from the drop down box at the top of the page For re-configuration of the sensor, the LCT MUST be connected in the safe area, behind the protection of a safety barrier or isolator Voltage MUST be supplied by a suitably rated safety barrier or isolator. They comply with the European ATEX Directive 2014/34/EU and are covered by certificates for IECEx (international), TIIS (Japan) and UKCA (United Kingdom).Īll models of the ExTemp have been issued an ATEX (CML 14ATEX2079) Certificate for use in both gas and dust explosive atmospheres in above ground installations. All models have been certified Intrinsically Safe for use in gas and dust hazardous areas by Certification Management Ltd. These sensors are designed primarily for use in hazardous areas in conjunction with a suitable safety barrier or isolator. The optional LCT Loop Configuration Tools (USB and RS-485 adapters) and free software allow the ExTemp to be connected to a PC, PLC or SCADA system for temperature indication, sensor configuration and data acquisition. A choice of precision optics is available to measure small or large targets at short or long distances. All models have an adjustable emissivity setting, and may be used to measure a wide variety of target materials, including food, paper, textiles, plastics, leather, tobacco, pharmaceuticals, chemicals, rubber, coal, asphalt and paint. Temperature ranges from -20☌ to 1000☌ are available. It is certified to ATEX, IECEx and TIIS standards.Įxplosion proof pyrometers typically have bulky, expensive housings, however because the ExTemp uses Intrinsic Safety as the method of protection, it is compact and low-cost. It measures the temperature of surfaces in hazardous areas without contact, and provides a direct 4-20 mA output. The ExTemp is an intrinsically safe pyrometer. Stainless steel 316 housing, ideal for offshore applications.Cable may be extended even further (subject to safety requirements) - cable runs could extend all the way back to the control room.Optional RS-485 network adapter and USB configuration tool.ATEX and IECEx certified up to Zone 0 (gas) and Zone 20 (dust).The DRF series is rated for 2500 VDC isolation, is UL approved, and is RoHS compliant. Adding optional accessory DIN-02 base plate converts the chassis mount case to a standard Din-Rail mount. ![]() The enclosed case has external terminal blocks for ease of connection and is chassis mountable. The units are encapsulated with a thermally conductive potting compound in a plastic resin and fiberglass case that meets UL94V-0. The series has output over-voltage and short circuit protection. The DRF series offers output voltages from 5.1 VDC to 48VDC, with input ranges of 9-36 and 18- 75 VDC, while achieving efficiencies up to 92%. The optional Din-Rail mount and terminal blocks enable it to be used as a power solution in an assortment of applications. The DRF Series offers 40 Watts of output power in an encapsulated case, for ruggedized backplane applications. NovemConTech, a Division of Calex Mfg., announced the DRF series of chassis mount DC/DC converters. ConTech announces DRF series of DC/DC converters ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |